|
Product Details:
|
| Product Name: | Fiber Transceiver | Wavelength: | 850nm |
|---|---|---|---|
| Distance: | 550m | Data Rate: | 10Gb/s |
| Interface: | Dual LC | Power Supply: | Single +3.3V |
| Warranty: | 3 Years | Application: | Ethernet,Fiber Channel,Switch To Switch Interface |
| High Light: | bidirectional fiber optic transceiver,fiber optic sfp module |
||
Absolute Maximum Ratings
| Parameter | Symbol | Min. | Max. | Unit | Note |
| Supply Voltage | Vcc | -0.5 | 4.0 | V | |
| Storage Temperature | TS | -40 | 85 | °C | |
| Relative Humidity | RH | 0 | 85 | % |
Note: Stress in excess of the maximum absolute ratings can cause permanent damage to the transceiver.
General Operating Characteristics
| Parameter | Symbol | Min. | Typ | Max. | Unit | Note |
| Data Rate | DR | 9.95 | 10.3125 | 11.3 | Gb/s | |
| Supply Voltage | Vcc | 3.13 | 3.3 | 3.47 | V | |
| Supply Current | Icc5 | 500 | mA | |||
| Operating Case Temp. | Tc | 0 | 70 | °C | ||
| TI | -20 | 80 |
Electrical Characteristics (TOP(C) = 0 to 70 ℃, TOP(I) =-20 to 80 ℃,VCC = 3.13 to 3.47 V)
| Parameter | Symbol | Min. | Typ | Max. | Unit | Note |
| Transmitter | ||||||
| Differential data input swing | VIN,PP | 120 | 820 | mVpp | ||
| Transmit Disable Voltage | VD | 2.0 | Vcc | V | 1 | |
| Transmit Enable Voltage | VEN | Vee | Vee+0.8 | |||
| Input differential impedance | Rin | 100 | Ω | 2 | ||
| Transmit Disable Assert Time | Tda | 10 | us | |||
| Receiver | ||||||
| Differential data output swing | Vout,pp | 340 | 850 | mVpp | 3 | |
| Output rise time and fall time | Tr, Tf | 38 | Ps | 4 | ||
| LOS Fault | VLOS_F | VCC-0.5 | Vcc | V | 5 | |
| LOS Normal | VLOS_N | Vee | Vee+0.5 | V | 5 | |
Notes:
1. Or open circuit.
2. After internal AC coupling.
3. Into 100 ohms differential termination.
4. 20 – 80 %.
5. Loss Of Signal is open collector to be pulled up with a 4.7k~ 10k resistor to 3.15 – 3.6V.
Logic 0,indicates normal operation; logic 1 indicates no signal detected.
Optical Characteristics (TOP(C) = 0 to 70 ℃, TOP(I) =-20 to 80 ℃,VCC = 3.13 to 3.47 V)
| Parameter | Symbol | Min. | Typ | Max. | Unit | Note |
| Transmitter | ||||||
| Operating Wavelength | λ | 1260 | 1270 | 1280 | nm | |
| 1320 | 1330 | 1340 | ||||
| Ave. output power (Enabled) | PAVE | -3 | 3 | dBm | 1 | |
| Side-Mode Suppression Ratio | SMSR | 30 | dB | |||
| Optical Modulation Amplitude | POMA | -2.8 | 0 | dB | OMA | |
| Extinction Ratio | ER | 4 | 4.5 | dB | ||
| RMS spectral width | Δλ | 0.45 | nm | |||
| Rise/Fall time (20%~80%) | Tr/Tf | 45 | ps | |||
| Dispersion penalty | TDP | 3.2 | dB | |||
| Relative Intensity Noise | RIN | -130 | dB/Hz | |||
| Output Optical Eye | Compliant with IEEE 0802.3ae | |||||
| Receiver | ||||||
| Operating Wavelength | λ | 1320 | 1330 | 1340 | nm | |
| 1260 | 1270 | 1280 | ||||
| Receiver Sensitivity(ER=4.5) | PSEN1 | -12.6 | dBm | 2 | ||
| Receiver Sensitivity(ER=6) | PSEN2 | -14.4 | dBm | 2 | ||
| Average Receive Power | PAVE | 0.5 | dBm | |||
| Receiver Reflectance | Rrx | -12 | dB | |||
| LOS Assert | Pa | -30 | dBm | |||
| LOS De-assert | Pd | -17 | dBm | |||
| LOS Hysteresis | Pd-Pa | 0.5 | dB | |||
Notes:
1. Average power figures are informative only, per IEEE 802.3ae.
2. Measured with worst ER; BER<10-12; 231 – 1 PRBS.
| PIN # | Name | Function | Name/Description | Notes |
| 1 | GND | Module Ground | 1 | |
| 2 | VEE5 | Optional -5.2V Power Supply (Not requireed) | ||
| 3 | LVTTL-I | MOD_DESEL | Module De-select; When held low allows the module to respond to 2-wire serial interface | |
| 4 | LVTTL-O | INTb | Interrupt; Indicates presence of an important condition which can be read via the 2-wire serial interface | 2 |
| 5 | LVTTL-I | TX_DIS | Transmitter Disable; Turns off transmitter laser output | |
| 6 | VCC5 | +5V Power Supply (Not required) | ||
| 7 | GND | Module Ground | 1 | |
| 8 | VCC3 | +3.3V Power Supply | ||
| 9 | VCC3 | +3.3V Power Supply | ||
| 10 | LVTTL-I/O | SCL | 2-Wire Serial Interface Clock | 2 |
| 11 | LVTTL-I/O | SDA | 2-Wire Serial Interface Data Line | 2 |
| 12 | LVTTL-O | MOD_Abs | Indicates Module is not present. Grounded in the Module | 2 |
| 13 | LVTTL-O | MOD_NR | Module Not Ready; Indicating Module Operational Fault | 2 |
| 14 | LVTTL-O | RX_LOS | Receiver Loss Of Signal Indicator | 2 |
| 15 | GND | Module Ground | 1 | |
| 16 | GND | Module Ground | 1 | |
| 17 | CML-O | RDN | Receiver Inverted Data Output | |
| 18 | CML-O | RDP | Receiver Non-Inverted Data Output | |
| 19 | GND | Module Ground | 1 | |
| 20 | VCC2 | +1.8V Power Supply (Not required). | ||
| 21 | LVTTL-I | P_DOWN/RST | Power down; When high, requires the module to limit power consumption to 1.5W or below. 2-Wire serial interface must be functional in the low power mode. | |
| 21 | LVTTL-I | P_DOWN/RST | Reset; The falling edge initiates a complete reset of the module including the2-wire serial interface, equivalent to a power cycle. | |
| 22 | VCC2 | +1.8V Power Supply (Not required) | ||
| 23 | GND | Module Ground | 1 | |
| 24 | PECL-I | REFCLK+ | Not used, internally terminated to 50ohm (100ohm diff). | 3 |
| 25 | PECL-I | REFCLK- | Not used, internally terminated to 50ohm (100ohm diff). | 3 |
| 26 | GND | Module Ground | 1 | |
| 27 | GND | Module Ground | 1 | |
| 28 | CML-I | TD- | Transmitter Inverted Data Input | |
| 29 | CML-I | TD+ | Transmitter Non-Inverted Data Input | |
| 30 | GND | Module Ground | 1 |
Notes:
Notes:
1. Module circuit ground is isolated from module chassis ground within the module.
2. Open collector; should be pulled up with 4.7k – 10k ohms on host board to a voltage between 3.15Vand 3.6V.
3. Reference Clock input is not required.
Ordering Information
| XFP Bidi,9.95 to 11.3Gb/s, 1270/1330nm, 20km, 0~70℃, with Digital Diagnostic Monitor |
| XFP Bidi,9.95 to 11.3Gb/s, 1330/1270nm, 20km, 0~70℃, with Digital Diagnostic Monitor |
| XFP Bidi,9.95 to 11.3Gb/s, 1270/1330nm, 20km, -20~80℃, with Digital Diagnostic Monitor |
| XFP Bidi,9.95 to 11.3Gb/s, 1330/1270nm, 20km, -20~80℃, with Digital Diagnostic Monitor |
●10GBASE-LR at 10.3125Gbps
●10GBASE-LW at 9.953Gbps
●Other optical link
FAQ
Q1. Can I have a sample order for this product?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.
Q2. What about the lead time?
A:Sample needs 3-6 days, mass production time needs 1-2 weeks for order quantity more than
Q3. Do you have any MOQ limit for sample order?
A: Low MOQ, 1pc for sample checking is available
Q4. How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline and sea shipping are also optional.
Contact Person: Alice Cai
Tel: +86 13530265603
